Effects of various sintering methods on microstructure and mechanical properties of CP-Ti powder consolidations
DC Field | Value | Language |
---|---|---|
dc.contributor.author | Shon, Je-ha | - |
dc.contributor.author | Park, Jong-moon | - |
dc.contributor.author | Cho, Kyeong-sik | - |
dc.contributor.author | Hong, Jae-keun | - |
dc.contributor.author | Park, Nho-kwang | - |
dc.contributor.author | Oh, Myung-hoon | - |
dc.date.available | 2020-04-24T12:25:29Z | - |
dc.date.created | 2020-03-31 | - |
dc.date.issued | 2014-07 | - |
dc.identifier.issn | 1003-6326 | - |
dc.identifier.uri | https://scholarworks.bwise.kr/kumoh/handle/2020.sw.kumoh/2031 | - |
dc.description.abstract | Effects of various sintering methods such as spark plasma sintering (SPS), hot pressing (HP) and electric resistance sintering (ERS) on the microstructure and mechanical properties of commercial pure titanium (CP-Ti) powder consolidations with particle size of <147 mu m, <74 mu m and <43 mu m were studied. The smaller particle powders are densified to proceed at a higher rate. Dense titanium with relative density up to 99% is found to take place at 850 degrees C under 30 MPa of SPS and HP condition. However, in case of ERS, CP-Ti powders were densified almost at 950 degrees C under 30 MPa. The microstructure of sintered titanium is composed of equiaxed grains at 850-950 degrees C. The yield strength of sintered body composed of <43 mu m powder is 858 MPa by using SPS at 850 degrees C under 30 MPa. When there is a higher content of small particle, the higher yield strength value is obtained both by using SPS and HP. However, when ERS is introduced, the highest yield strength is 441 MPa at 950 degrees C under 30 MPa, which shows much lower values than those by SPS and HP methods. ERS method takes much less sintering time compared with SPS and HP. Nevertheless, higher sintering temperature results in lower strength and elongation because of brittle fracture. | - |
dc.language | 영어 | - |
dc.language.iso | en | - |
dc.publisher | ELSEVIER | - |
dc.subject | TITANIUM | - |
dc.subject | PRESSURE | - |
dc.subject | FABRICATION | - |
dc.subject | RESISTANCE | - |
dc.subject | KINETICS | - |
dc.title | Effects of various sintering methods on microstructure and mechanical properties of CP-Ti powder consolidations | - |
dc.type | Article | - |
dc.contributor.affiliatedAuthor | Cho, Kyeong-sik | - |
dc.identifier.doi | 10.1016/S1003-6326(14)63289-1 | - |
dc.identifier.scopusid | 2-s2.0-84905852061 | - |
dc.identifier.wosid | 000352613200009 | - |
dc.identifier.bibliographicCitation | TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA, v.24, pp.S59 - S67 | - |
dc.citation.title | TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA | - |
dc.citation.volume | 24 | - |
dc.citation.startPage | S59 | - |
dc.citation.endPage | S67 | - |
dc.type.rims | ART | - |
dc.type.docType | Article | - |
dc.description.journalClass | 1 | - |
dc.subject.keywordPlus | TITANIUM | - |
dc.subject.keywordPlus | PRESSURE | - |
dc.subject.keywordPlus | FABRICATION | - |
dc.subject.keywordPlus | RESISTANCE | - |
dc.subject.keywordPlus | KINETICS | - |
dc.subject.keywordAuthor | CP-Ti powders | - |
dc.subject.keywordAuthor | sintering method | - |
dc.subject.keywordAuthor | spark plasma sintering | - |
dc.subject.keywordAuthor | hot pressing | - |
dc.subject.keywordAuthor | electrical resistance sintering | - |
Items in ScholarWorks are protected by copyright, with all rights reserved, unless otherwise indicated.
350-27, Gumi-daero, Gumi-si, Gyeongsangbuk-do, Republic of Korea (39253)054-478-7170
COPYRIGHT 2020 Kumoh University All Rights Reserved.
Certain data included herein are derived from the © Web of Science of Clarivate Analytics. All rights reserved.
You may not copy or re-distribute this material in whole or in part without the prior written consent of Clarivate Analytics.